Lighter 1300 Degree Torch Jet Flame Pencil Butane Gas Refillable Fuel Welding Soldering Pen Outdoor | Инструменты

Lighter 1300 Degree Torch Jet Flame Pencil Butane Gas Refillable Fuel Welding Soldering Pen Outdoor | Инструменты

Lighter 1300 Degree Torch Jet Flame Pencil Butane Gas Refillable Fuel Welding Soldering Refillable Fuel Pen Outdoor Lighter

Specification:

Color:Black

Package:1PC soldering torch pen

1. How to operate the correct inflation:

1. Before inflating, use a small
tool to hold the inflatable core, completely discharge the residual gas
inside, and eliminate the pressure in the gas tank of the lighter;

2. Press the aerated gas tank outlet vertically downwards, pressing for about 5 seconds each time, two or three times.

3. Please wait for about 5 minutes
after the inflation is completed. If there is still no fire after 5
minutes, please adjust the adjustment valve to a larger value (see + -
symbol).

2. Detailed inflation introduction:

Gas filling method

1. When refilling, there must be no Mars or fire around, so be sure to be safe. Do not refill while smoking;

2. Qualified butane gas should be used. Inferior gas may damage the lighter or reduce the service life;

3. When refilling the normal
model, please stand up the lighter, align the gas outlet of the gas
bottle and cover the air inlet of the lighter, press it several times,
keep it for about 2 seconds each time; if the gas cannot be filled, it
may be steam. Excess air is left in the box. At this time, you can
deflate, use a small screwdriver to align the air inlet and deflate 1-2
times, and then perform the air filling operation;

4. When the sound is refilled,
please loosen the air inlet screw cover with a flat-blade screwdriver
and then follow the above steps. After the filling is completed, the
screw cap can be flattened, not too tight; otherwise, the cover will not
be dense and the cover will not be crisp, and the gas will escape. The
hard-mounted vocal machine should be equipped with a special air nozzle
to refill the air; 5, when the gasoline engine is refueling, the head
cover should be opened, the movement should be pulled out and reversed,
the outer sponge should be opened and the appropriate amount of gasoline
should be added, and the gasoline should be infiltrated into the inner
layer and covered. The outer sponge is then placed inside the casing;

5. After all kinds of lighters
are refueled, wait at least 1 minute to adjust the temperature of the
newly charged gas to room temperature, and then ignite after the
residual gas attached to the lighter is completely evaporated. If the
ignition operation is performed immediately at this time, the residual
gas on the outside of the lighter may be burned, posing an unnecessary
danger. After refilling the gas, if the flame height is too high or too
low when used, it is a normal phenomenon, and the flame height can be
moderately adjusted.

Adjusting the flame:

1. When using, as the gas content
of the product decreases and the ambient temperature changes, the flame
height will change to a certain extent. This is a normal phenomenon, you
can adjust the flame height moderately;

2. When used, the normal flame
height should be adjusted; the windproof and straight-through type
lighters are 1.5-2.5 cm; the vocal, gasoline and open flame lighters are
2.5-4.0 cm;

3. If you need to adjust the
height of the flame, please use a flat-blade screwdriver to align the
groove of the flame regulator; if the lighter itself has an adjustment
ring, you can adjust it directly with your finger, and turn it clockwise
in the direction of the (-) arrow. Adjustable low flame height; turn
counterclockwise toward (+) arrow to increase flame height. Note: Rotate
counterclockwise and cannot exceed half a turn on a normal flame
height. Otherwise, it may damage the product;

4. The gasoline lighter should
control the flame height by adjusting the height of the ignition wick.
If the flame height is too high, use a pair of scissors to cut the wick a
little; if the flame height is too low, the wick can be properly pulled
out.

Precautions:

1. Contains pressurized flammable gas, please keep away from children;

2, do not puncture or throw a lighter, do not throw into the fire;

3. Please use in a ventilated environment, pay attention to flammable materials;

4. It is strictly forbidden to
face flammable substances such as face, skin and clothing in the
direction of the fire head to avoid danger;

5. When igniting, please look for
the position of the fire exit, and press the ignition moderately.
Different styles of lighters are ignited in different ways: divided into
straight, side, and side; gasoline engine should quickly rub the wheel,
and the sound machine uses the thumb to quickly rub the roller from
right to left;

6. When using, if there is any
smog and other debris falling into the fire outlet, you should blow it
in time to remove the sundries, otherwise it will cause bad fire;

7, sound and gasoline lighter, if
the cover is opened, the gas will begin to escape. Therefore, when not
igniting, be sure to cover the cover to save;

8, this product is not suitable
for lighting, do not continue to burn for more than 1 minute, so as not
to burn the skin with high temperature;

9. Do not leave the lighter in a
high temperature environment for a long time (50 degrees Celsius / 122
degrees Fahrenheit), and avoid long-term direct sunlight, such as around
the stove, outdoor closed unmanned car and trunk;

10. Due to the limitation of
combustion conditions in the climate above 3000 meters above sea level,
the ignition of windproof and straight-through lighters may be greatly
affected. At this time, it is recommended to use an open flame lighter;

11. When using a handicraft
lighter such as a tabletop, the position of the fire exit, press, air
inlet, and flame regulator should be clearly defined.

12. Qualified butane gas should be used. Poor quality gas may damage the lighter or reduce the service life