WOODWARD easYgen-1800 Generator set controller AMF single machine automationJ1939+RS485 |

WOODWARD easYgen-1800 Generator set controller AMF single machine automationJ1939+RS485 |

WOODWARD easYgen-1800 Generator set controller AMF single machine automationJ1939+RS485

easYgen-1800 has all functions of easYgen-800 as well as automatic mains failure function (AMF), particularly well suited for single automation systems that include mains and generator.

easYgen-800 is intended to be used for single automation systems, auto start/stop of the unit are performed with the help of remote signal.

Functional Blocks

Ltem

easYgen-800      

easYgen-1800 

LCD (with backlight)                   

Dimension         

4.3"

4.3"

Pixel

480*272

480*272

AMF

no

•

Input Port Number

8

8

Output port Number

8

8

Sensor number

5

5

Neutral (earth) current

•

•

Schedule function

•

•

Ethernet

•

•

GSM

•

•

J1939

•

•

USB

•

•

Micro SD card (slot)

•

•

Real-time clock

•

•

Event log

•

•

Key characteristics

With ARM-based 32-bit SCM, highly integrated hardware, high reliability level

Multilingual interface (including English, Chinese or other customer specific languages) which can be chosen at the site, making commissioning convenient for factory personnel

Improved LCD wear-resistance and scratch resistance due to hard screen acrylic

Silicon panel and pushbuttons for better operation in high-temperature environment

RS-485 communication port enabling remote control, remote measuring, remote communication via ModBus protocol

SMS (Short Message Service) function: When genset is alarming, controller can send short messages via SMS automatically to max. 5 telephone numbers (external GSM modem is needed). Besides this, generator status can be controlled and checked.

Equipped with CAN bus port to communicate with J1939 genset. Monitoring frequently-used data such as water temperature, oil pressure, speed, fuel consumption and so on of ECU machine, and additionally also control start, stop, raising speed, and speed droop via CAN bus port

Suitable for 3-phase 4-wire, 3-phase 3-wire, single phase 2-wire, and 2-phase 3-wire systems with voltage 120/240 V and frequency 50/60 Hz

easYgen-1800 only: Collects and shows 3-phase voltage, current, power parameter and frequency of generator or mains. Mains Generator Line voltage (UAB, UBC, and UCA) Line voltage (UAB, UBC, and UCA) Phase voltage (UA, UB, and UC) Phase voltage (UA, UB, and UC)

easYgen-800 only: Collects and shows 3-phase voltage, current, power parameter and frequency of generator. Generator Line voltage (UAB, UBC, and UCA) Line voltage (UAB, UBC, and UCA) Phase voltage (UA, UB, and UC) Phase voltage (UA, UB, and UC)

Phase sequence, frequency, Load current IA, IB, IC

Each phase: Total active power [kW], Total reactive power [kvar], Total apparent power [kVA], Average power factor PF

Accumulated Total generator power [kWh], [kvarh], [kVAh], and Earth current

easYgen-1800 only: For Mains, controller has over and under voltage, over and under frequency, loss of phase and phase sequence wrong detection functions For generator, controller has over and under voltage, over and under frequency, loss of phase, phase sequence wrong, over and reverse power, over current functions

3 fixed analog sensors (temperature, oil pressure and fuel level)

Flexible sensors can be set as temperature sensor, oil pressure sensor or level sensor

Precision measure and display parameters about Engine, Temp. (WT) °C/°F both be displayed Oil pressure (OP) kPa/psi/bar all be displayed Fuel level (FL) %(unit) Speed (SPD) r/min (unit) Battery Voltage (VB) V (unit) Charger Voltage (VD) V (unit) Hour count (HC) can accumulate to max. 65535 hours. Start times can accumulate to max. 65535 times

Protection: automatic start/stop of the genset, ATS (Auto Transfer Switch) control with perfect failure indication and protection function

All output ports are relay-out Parameter setting: parameters can be modified and stored in internal FLASH memory and cannot be lost even in case of power outage; most of them can be adjusted using front panel of the controller and all of them can be modified using ToolKit-SC configuration software on PC via USB, Ethernet, or RS485 ports

More kinds of curves of temperature, oil pressure, fuel level can be used directly and users can define the sensor curves by themselves

Multiple crank disconnect conditions (generator frequency, speed sensor, oil pressure) are optional

Widely power supply range DC (8 to 35) V, suitable to different start battery voltage environment

Event log, real-time clock, scheduled start & stop generator (can be set as start genset once a day/week/month whether with load or not)

Logon wallpaper and display time are user-defined

Can be used on pumping units and as an indicating instrument (indicate and alarm are enable only, relay is inhibited)

With maintenance function. Actions (warning or shutdown) can be set when maintenance time out

All parameters are digital adjusted (instead of conventional analog modulation with normal potentiometer) for more reliability and stability

Waterproof security level IP55 due to rubber seal installed between the controller enclosure and front panel

Metal fixing clips enable perfect in high temperature environment

Modular design, self-extinguishing ABS plastic enclosure, pluggable connection terminals and embedded installation way; compact structure with easy mounting

Accumulation of total run time and total electric energy of A and B. Users can reset it for convenience.

Functions

Protection: automatic start/stop of the genset, ATS (Auto Transfer Switch) control with failure indication and protection function

All output ports are relay-out

Parameter setting: parameters can be modified and stored in internal FLASH memory and cannot be lost even in case of power outage; most of them can be adjusted using front panel of the controller and all of them can be modified using ToolKit-SC on a PC via USB or RS485 ports.

Curves of temperature, oil pressure, fuel level can be used directly and users can define the sensor curves by themselves

Multiple crank disconnect conditions (generator frequency, speed sensor, oil pressure) are optional

Event log, real-time clock, scheduled start & stop generator (can be set as start genset once a day/week/month whether with load or not)

Logon wallpaper and display time are user-defined

Can be used on pumping units and as an indicating instrument (indicate and alarm are enable only, relay is inhibited)

Maintenance function: Actions (warning or shutdown) can be set when maintenance time out

All parameters use digital adjustment, instead of conventional analog modulation with normal potentiometer for more reliability and stability

Accumulative total run time and total electric energy of A and B. User can reset it as 0 and re-accumulative the value which allows to count the total value user defined.