Heropie Rechargeable And Waterproof Remote Dog Training Collar Vibration Shock Electronic Electric 300M 100Lv Anti Bark Control | Дом и сад

Heropie Rechargeable And Waterproof Remote Dog Training Collar Vibration Shock Electronic Electric 300M 100Lv Anti Bark Control | Дом и сад

Important notice:
The Receiver Collar works only if it is correctly encoded with Remote Transmitter, therefore, please follow the setup steps in User Manual carefully when you use the tool for the first time.

belt dog,arnes correa perros,correa retractil perro,clicker for dogs

Description:

1. Antenna: transmit the signal to Receiver Collar

2. LED lamp: the lamp will light when you press the button of LED light

3. LED Indicator lamp: the light will flash when the transmitter is working. The lamp will light when it is being charged.

4. LCD Screen:

Static mode: under this mode, press "Y" button, Receiver will shock; press up/down button, can adjust the level of Static shock from 0 to 100.

Vibration mode: under this mode, press “Y” button, Receiver will vibrate; press up/down button, an adjust Vibration level from 0 to 100.

Beep mode: under this mode, press "Y" button, Receiver collar can get beep sound.

Light mode: under this mode, press "Y" button, the green LED light in the Receiver will flash every one second, it is convenient to let you know where your pet is.

Channel 1: select to encode between transmitter and one of receiver collar

Channel 2: select to encode between transmitter and 2nd of receiver collar

5. Up/down button: intensity level button for Vibration and Static Shock

6. LED lamp button: when pressing the LED light button, the lED lamp in the Transmitter will light

7. Channel button: press the button, can select to encode between transmitter and one of receiver collar, or another one

8. Launch button: after you finish mode select, press this button for confirmation.

9. Mode button: include 4 modes: Static Mode, Vibration Mode, Beep Mode and LED lamp mode

10. Charging hole: charge for Remote Controller

11. Contact points: deliver the safe static correction

12. Rest hole: turn on/off the receiver

13. DV-5V hole: charge for receiver

Features:

100% Brand New and High Qualit

With compact portable design

Easy to use, ergonomic transmitter.

Waterproof for training in bad weather and keep the inside of collar against wet.

Rechargeable collar with USB Charge cable

Rheostat’s dial that allows to gradually increasing the stimulus intensity within 0-100 levels

4 training modes: static shock/vibration/beep/light

Two dog modes allow the trainer to control two different dogs from one transmitter.

Featured power saving design with automatic standby and memory function

No external antenna on the collar receiver

Reduced receiver/collar is ideal for small/medium size dogs

The liquid crystal digital display let the operation become simple

Specification:

Frequency: 433.825MHz

Transmitter: 3.7V 500ma Lip

Receiver: 3.7V 500ma Lip

Color: Black

Package weight: 10.0 oz

How to use:

1. Charge the remote transmitter/receiver:

1) Connect the charger's connector to the charging jack (DC-5V hole)

2)Connect usb cable for charging

3) The red light on the transmitter will be lighted

4) Charge the transmitter/receiver at least 6 hours for the first charge

5) After fully charged, the red LED lamp will be turned off automatically (Important note: Low battery indicator: the symbol will show on the LCD screen)

2. Connect transmitter and receiver:

1) Turn on the transmitter by pressing any button on the transmitter

2) Press "1/2" button to choose channel for connection, choose channel 1 for the first receiver

3) Lift the rubber cover of the Reset part on the receiver. Press the Reset button inside of the receiver with a pen or paper clip, and the green LED light will turn on

4) After a Beep came from the receiver, press the "Y" button on the transmitter within 10 seconds

5) The collar receiver will beep if successfully connected

6) Press "1/2"button to encode, choose to channel 2 for second collar by the same procedure

Important notice:

1. The transmitter will go into Standby Mode after 20 seconds if there is no operation and turn off after 20 minutes

The receiver will go into Standby Mode if unused for 4 minutes. Any movement will activate the receiver.

2. "1/2" button to choose channel for connection. In channel 1, can only train the first receiver, in channel 2 train the second receiver

3. In working mode, if you want to reconnect the receiver, simply use a pen or paper clip, press the reset button, there is a beep sound that indicates that it’s ready to encode

4. The receiver is designed to be waterproof. The rubber cover has to be put in the right position

Note:

  1. The lifetime of the batteries depends on how often you use the product. Therefore you should often check the batteries by hear the beep from the Collar Receiver and watching the indicating on the LCD screen of the transmitter

2. The valid distance of remote control means the straight-line distance between the transmitter and the Collar Receiver without obstacle. If there is interference signal or signal screening around, the actual remote control distance may be various.

3. This product is for pet training. Only by training, the pet can understand the intention of it power. Good effect can only be achieved after a period of training

4. Training session should be kept positive and short, about 10-15minutes long each time.

5. Presently, this product is the most effective and the safest tool for pet training. Follow the correct operational instructions, you can effectively train the pet and bring it no harm.  

FOR 1 DOG:

For two dogs:

Warm Notice:

1. Both Remote Transmitter and Receiver Collar are energy-saving designed. The Remote Transmitter will go into STANDBY MODE if there is no operation after 1 minute, and by pressing Mode button you can activate the transmitter from Standby mode. The Receiver Collar will go into Standby mode if no operation for 4 minutes. And any movement will activate the Receiver.

2. A startup roller is contained in Receiver Collar, so you will hear sound when the collar is shaking, don't mistake it as any parts falling off.

Encode signal transmission between Remote Transmitter and Receiver Collar:

1. Press Mode button to turn on Remoter Transmitter and adjust levels of Vibration and Static above 0.

2. Press “1/2” button to select a signal channel.

3. Open the rubber cap and press the switch button inside Receiver, which beeps once to indicate the Receiver is on.

4. Press Y button within 10 seconds to encode the signal, at the same time, the Receiver beeps once.

5. If you fail to press Y button within the 10 seconds period, please repeat steps above.

6. If you have 2 Receiver Collars, press again “1/2” button to select another signal channel for transmission encoding.

You need charge this product before you start using it for the first time.

How to charge Remote Transmitter:

1) Connect Remote Transmitter to a charger into a standard socket.

2) LED Indicator on Remote Transmitter turns red when charging.

3) Once Remote Transmitter is fully charged, the red LED indicator turns off automatically.

How to charge Receiver Collar

1) Open the rubber cap, connect Receiver Collar to a charger into a standard socket.
2) LED Indicator on Receiver Collar turns red when charging
3. After being fully charge, LED indicator turns yellow and goes into Standby mode if there is no movement.

Warm Notice:

1) Charge the Remote Transmitter and Receiver Collar at least 6 hours for the first charging.

2) Functions of Receiver Collar are disabled and out of control of Remote Transmitter when being charged.

3) Low battery indicator symbol   will be displayed on LCD screen.

4. Receiver Collar keeps beeping continuously if its voltage is under working level.

5) This product is rechargeable. To maintain its proper functions, please charge once a monthly if it is not used.

Warm Notice:

Remember your signal channel setup and don't change it frequently, otherwise remote control does not work!

Test Pet Trainer Training Collar
Static Shock function test

As static function is invisible to our naked eye, please use test light to verify the function.

First press Mode button to switch to Static mode. You can press UP/DOWN button on the right to confirm LCD index is above 0, as shown in the figure.

Press Y button on Remote Transmitter to see if the test light is on.

Vibration function test:

First press Mode button to switch to Vibration mode. You can press UP/DOWN button on the right to confirm LCD index is above 0.

Press Y button, the Receiver Collar will vibrate.

Beep alert function test:

First press Mode button to switch to Beep mode. No adjustment is needed under this mode, therefore LCD index displays 000.

Press Y button, the Receiver Collar will beep.

LED flash function test:

First press Mode button to switch to LED Light mode. No adjustment is needed under this mode, therefore LCD index displays 000.

Press Y button, the LED light on Receiver Collar will flash red continuously.

Please install nylon collar in accordance with the illustrated figure.

How to wear Receiver Collar correctly:

1. Correct wearing position helps healthy and effective pet training. Receiver shall be placed on bottom of your pet's neck, and the screw cap must contact pet's skin directly.

2. If your pet has a thick fur in the neck place, please use longer screw caps.

3. A spacing to hold a finger shall be maintained between Receiver Collar and your pet's skin. However the Receiver Collar can't be too loose, otherwise static effectiveness shall be badly influenced.

4. Too long Receiver Collar can be trimmed, or be handled with other methods.

Pet Trainer shutdown:

1. Remote Transmitter is energy-saving designed. The Remote Transmitter goes into Standby mode after 1 minute without movement, or you can press and hold Mode button for 3 seconds to shutdown.

2. Receiver Collar is energy-saving designed. The Receiver Collar goes into Standby mode after 4 minutes without movement, Press and hold for 3 seconds the switch inside Receiver Collar to shutdown

Attention:

1. High-end transmission technology is used in the remote control Transmitter, therefore you need not aim directly at Receiver Collar, the signal can go through obstacles such as walls and other things, however, the effective distance will be decreased.

2. A list of factors, including but not limited to signal station, magnetic field, obstacle, battery volume, other wireless devices nearby, landform, vegetative cover, etc, shall also influence transmission of signals from remote transmitter and the actual effective distance of the Remote Transmitter.

3. This product is a pet trainer. Therefore, your pet can understand your intention only through actual training activities. Good outcomes could be achieved only after certain period of intensive training.

4. Keep active training, and each training shall not be too long, 10-15 minutes is suggested.

5. Currently, our product is the most effective and safest pet training tool in the market. Follow the correct training steps, you can get your pet effectively and successfully trained without being harmed.

6. Any other questions, please don't hesitate to contact us or our local dealers.

Regular maintenance:

Please examine regularly to ensure tightness of Remote Transmitter and eliminate any external damages.

Clean the screw caps with alcohol weekly.

Examine your pet's neck and carry out weekly cleanup.

Frequently Asked Questions (FAQ)

Q: How old does my pet have to be before using 998D Pet Training Collar?
A: Your pet should be able to recognize basic obedience commands such as ”Sit” or “Stay”. 998D Pet Training Collarmay be worn by most dogs of 25 kilograms and some dogs slightly over 25 kilograms.

Q: Once my pet is trained and has been obeying my commands, is it still necessary for my pet to continue to wear the Receiver Collar?
A: You may need to reinforce your pet's memory with the Receive Collar from time to time.

Q: Can I use 998D Pet Training Collar with more than one pet?
A: Yes, you can simply add one more Receiver Collar to the system to control two pets, because two signal channels are available with the Remote Transmitter.

Q: What is the effective distance of your Pet Trainer?
A: The effective distance could be as far as 300 meters between Remote Transmitter and Receiver Collar without obstacles in between. However in reality, a list of factors, including but not limited to signal station, magnetic field, obstacle, battery volume, other wireless devices nearby, landform, vegetative cover, etc, shall influence transmission of signals from Remote Transmitter and the actual effective distance of Remote Transmitter.

Q: I want to test Static Shock function of Receiver Collar myself, but it does not work, is anything wrong?
A: If you test Receiver Collar by your hand or leg, please touch the 2 screw caps (electrodes) at the same time, touching only one screw cap (electrodes) will not work.

Q: How long can I continuously deliver vibration or Static Shock to my pet?
A: The maximum amount of time you can press the Vibration or Static Shock to your pet continuously is 10 seconds. After this, the Remote Transmitter will time-out, and you have to release Y button and press Y button again to restart Vibration or Static Shock function.

Q: Is the Receiver Collar of 998D Pet Training Collar waterproof?
A: Your pet can wear it when drinking water or in rainy days, however your pet can't wear it when swimming or diving.

Q: What do I do if my pet's neck becomes red and irritated?
A: Discontinue use of the Pet Trainer for a few days. If the condition persists beyond 48 hours, see your veterinarian. Even if the skin returns to normal, monitor your pet's skin condition closely.

Q: Can I attach a leash to the Receive Collar?
A: NO. This can result in pulling the Screw Caps (contact points) too tightly against your pet's neck. Use a separate collar placed above the Receiver Collar.

Q: How will I know when to charge the batteries of the Pet Trainer?
A: For Remote Transmitter: the symbol   will show up on the right down side of LCD screen. For Receiver Collar: if you hear continuous beep sound, you have to get it charged.

Q: How long is your lithium battery lifetime?
A: Our Lithium battery can be charged 400 times for remote Controller and Receiver Collar.

Q: How long can I leave Receiver Collar on my dog?
A: The Receiver Collar is not designed to be worn constantly. We recommend the Collar not be worn for more than 18 hours out of every 24-hour period. In case of longer time, you are advised to examine your pet regularly.

Q: How long should I process my training session for my pet?
A: Training sessions should be kept positive and short, it is better for about 10-15 minutes long each time.

Q: How long is the Receiver Collar?
A: Total length is 60CM, just trim it to proper length if it is too long.

Q: What are the proper levels of Vibration and Static Shock for my pets?
A: Try to find the best suitable levels of Vibration and Static Shock for your pet starting from the lowest level. Excessive levels of stimulation shall cause strong response from your pet.


Q: Any other better training methods?
A: You can prepare some dog food for training incentive to achieve better training outcomes.
Each time after you restrain your pet's misbehavior, you can tell your pet what is supposed to do and what is not supposed to do. And after a number of repetitions your pet understand what you like and what you don't like.

Q: How long will it take to get my pet trained well?
A: It takes time to eliminate a misbehavior or teach an obedience command. Please be patient. Overquick training may not lead to ideal outcomes.

Q: The 998D Pet Training Collar does not work, or my pet does not respond after correct installation of the Pet Trainer, how should I solve this problem?
A: Make sure both Remote Transmitter and Receiver Collar have enough power to operate.
Intensity level has to setup at over ”0” when encoding, test to launch for Vibration and Static Shock function.
Check to see if Receiver Collar is turned on.
Check “1/2” button on Remote Transmitter to ensure Signal Channels are correctly configured.
Try re-encoding Remote Transmitter and Receiver Collar.
Take off Receiver Collar and test all of the four functions work properly.
Receiver Collar goes into Standby mode after 4 minutes without movement. And any gentle movement can activate it.
Make sure Receiver Collar is properly worn and the collar can't be too loose.
Trim your pet's fur where the screw caps (contact points) touch the neck and/or change to the longer contact points.